India · Mid Level
Applicants who checked fit first are 3.1× more likely to hear back
Your score for this role already exists
ASAI compared this JD against 41 signals - skills, seniority, domain, stack overlap etc. Add a resume and it unlocks in about 30 seconds.
Always free · no credit card · 1 tap with Google
HIGH
Our tracked job listings for Larsen & Toubro show strong recent activity.
First 72 hours
Window passed - posted 6d agoEarly applicants get seen before the pile builds.
Not a repost
The first time we've seen this listing - it hasn't been closed and reopened.
You almost certainly match several of these already. Unlock your skill map to see the matches, the gaps, and what to fix first.
1.Should have knowledge of maintenance, trouble shooting & operation of auxiliaries for generator (upto 1000 MW) like single & double flow seal oil system, stator coil cooling water, lubrication oil system, jacking oil system, H2 & CO2 handling.
2.Should have knowledge of electrical testing on stator & rotor manufacturing :
a.Generator stator:
i.Insulation resistance measurement
ii.DC winding resistance
iii.Tan delta & capacitance measurement
iv.Partial discharge measurement
v.NFT of overhang winding
vi.Core loop flux test
vii.ELCID
b.Generator rotor :
i.Insulation resistance measurement
ii.DC winding resistance
iii.Impedance measurement
iv.RSO
3.Should have knowledge of generator routine & type test during dynamic condition:
a.Temperature rise – heat run
b.Open circuit test
c.Short circuit test
d.Sudden short circuit test
e.Negative sequence & Positive sequence test
f.THF & Voltage waveform deviation
4.Should have knowledge of IEC, ISO standards for electrical testing of generator ( up to 1000 MW) & High-speed balancing of turbine / generator rotors
5.Should have knowledge of Low speed & high-speed balancing of turbine & generator rotors
6.Should have knowledge of assembly of rotors in high-speed balancing tunnel
a.Able to visually check rotor
b.Able to take TOP / Side clearance of bearing & rotor journal
c.Able to perform alignment of rotor with motor shaft
d.Able to trouble shoot issues pertaining in assembly process
7.Can study P&ID, electrical drawings for maintenance & operation parameters
8.Have a positive approach for trouble shooting of electrical, mechanical & instrumentation issues in generator testing, high speed balancing &
9.Able to handle unionized workmen in shift, ready to work in shifts
10.Additional Vibration category – 2 certification is preferable
11.Able to handle customer at site for overhauling activities like in-situ balancing, electrical test on generator stator & rotor, calibration of instruments & operation/maintenance of auxiliaries, ready to travel at different sites
12.Should have knowledge of basic instrumentations/transducers like pressure transmitter, pressure gauge, RTD, Thermocouple etc.
13.Able to operate electrical testing kits like
a.Insulation tester
b.High voltage test set-up
c.Micro-ohm meter
d.PD kit
e.Tan- delta kit
f.Function generator
g.1- phase variac
Your match score, skill map and tracker stay free.
Skip jobs with hidden dealbreakers. See what they actually need, what's easy to miss, and how they describe the team.
Ground Reality on every job, plus Insider Path, practice interviews and resume tailoring.
We help you find people there who worked or studied where you did, and draft your first message and follow-up.
Free · no signup
Daily job drops, skill trends and free resources - posted straight to the group. Leave any time.
No spam. Just jobs and resources.
Why people use ASAI
Scored, not searched. Every role ranked against your actual profile.
Alerts as often as hourly. Reach new roles while the pile is still small.
Skill gaps, spelled out. See exactly which requirements you don't meet yet.
Verified jobs, only. Say no to ghost jobs. Your time deserves respect.
Keep browsing